Developer Portal Community
- Top Results
See all results
- Community
- About CtrlDiogoC
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
About CtrlDiogoC
since
12-18-2023
2 weeks ago
CtrlDiogoC
Established Member
24
Posts
1
Likes
2
Solutions
2 weeks ago
Hello, Thank you in advance for your reply. I later found the issue. It had to do with the View and DialogRequest variables. I had only created one variable for each and used them in the HMI configuration of the different units. I then created different HMI variables for each unit and solved the issue.
... View more
2 weeks ago
Hello, I have an issue: whenever I want to show a dialogue in the HMI, the requested view is always the unit where the CM addon is placed. How can I disable this behaviour? It's preventing me from doing the UserGuidance for the MES@AE changeover sequence, among other things. Thank you in advance.
... View more
3 weeks ago
Hello, We have a 3-axis system, controlled by a ctrlX DRIVE XCS (SoE) (1 axis) and a ctrlX DRIVE XMD (SoE) (2 axis). Whenever we perform a PLC Start/Restart, or a Reset Cold, we get the following error, by the CNC Portal object: The only way to recover is by doing an Activate Configuration, or when Start/Restart, to perform a power cycle to the controllers. As you can see in the following screenshot, the controllers themselves are error free: Thank you in advance.
... View more
10-21-2024
07:33 AM
After reaching out Nexeed Helpdesk, we realized that in the current version (V1.2.8.0), the PosToleranceX and PosToleranceXY parameters shouldn't be part of a DataSet, for the following reason:
... View more
10-16-2024
09:15 AM
No, it does not switch off U_A voltage. As you suggested, I tried to disconnect the AES channel to SafetyValveAddon, however, CPS exports an error pragma line to TwinCAT:
... View more
10-16-2024
08:55 AM
Hello, I'm developing a sequence of changeover, which requires the operator to open the door in one of the sequence steps. We have an Air Treatment Unit from Aventics, according to the standard (AES-D-BC-ECAT Gen2 peripheral). When the sequence gets to the door opening step, the control goes OFF, and it gets cancelled due to the following error: Is there any way of getting rid of this error? Thank you in advance.
... View more
10-14-2024
03:10 PM
Hello, Any news on this topic?
... View more
10-10-2024
12:26 PM
Hello Tommy, I have only tested the CALIBRATION command yet. So yes, it's during a CALIBRATION command.
Loc114E611_Captron.Unit.Command := AtmoCaptronCmd.CALIBRATION;
Loc114E611_Captron.Unit.ParCmd.StartPosXAxis := X_START_CALIB_COORDINATE;
Loc114E611_Captron.Unit.ParCmd.CalibDiameter := Loc114_NeedleCheck.ActiveDataSet.CalibDiameter;
Loc114E611_Captron.Unit.ParCmd.Resolution := Loc114_NeedleCheck.ActiveDataSet.Resolution;
Loc114E611_Captron.Unit.ParCmd.PosToleranceXY := Loc114_NeedleCheck.Unit.ParImm.HMIData.PosToleranceXY;
Loc114E611_Captron.Unit.ParCmd.VelLimit := Loc114_NeedleCheck.ActiveDataSet.VelLimit;
Loc114E611_Captron.Unit.Execute := TRUE;
... View more
10-09-2024
03:38 PM
Hello, I have a CNC Portal for dispensing purposes, with a Captron to calibrate the tool centre point. I have developed the calibration sequence in the order that is mentioned in the Captron object documentation: I also followed the documentation for the movement of the axes. The X coordinate stays the same throughout the movement, while Y changes in the negative direction. After the CNC stops, and when checking for the READY state from both objects, I get the following error: I have set the following parameters and tried to increase the X tolerance to 10 mm, however without success. Thank you in advance.
... View more
10-08-2024
06:48 PM
Hello, I have a machine that needs a CG mode and from what I've seen, Nexeed already provides an object to make it easier (CG addon and probe). When I try to add it to my project, I get the "Version Conflict" error: I've tried adding the V1.1.0.0 object but other objects depend on the V1.3.6.0 NxDataDefBase object. My CPS version is V5.6.2. Thank you in advance.
... View more
Latest Tags
No tags yet
Still looking for something?
- Top Results
See all results